August 2004 - modeller_usage

problem_2
by vivek sharma 25 Aug '04

25 Aug '04

Sir, The MAPRES problem is solved , I needed to remove some atoms from the topology file to bring number less than 100 (which is hard coded value = 100). The heme molecules like heme a and heme o , contains more than 100 atomtypes (if hydrogens are included) and MAPRES limit is crossed in this case, but without Hydrogens being counted it goes pretty well. As in your topology file you have given MASS values of some Hydrogens while in in RESI types you didn't mentioned Hydrogens, why this is so? PLease clarify. Now, I have another problem: Running modeler gives such warnings: -------------- iatmcls_286W> MODEL atom not classified: HEB:FE HEB iatmcls_286W> MODEL atom not classified: HEB:NA HEB -------------- why this is so? and finally it stops due to the following error: -------------- nselat__596E> Atom index is out of range (iatm,natm): 4338 4337 recover____E> ERROR_STATUS >= STOP_ON_ERROR: 1 1 -------------- what can be the reason for this reason ? please provide a solution to this problem. Thanks in advance. sincerely, vivek -- VIVEK SHARMA HBG BI

2 1

problem
by vivek sharma 23 Aug '04

23 Aug '04

Dear Modeler man, I have one problem in Modeler, it would be great if you can tell me the solution. Actually, I have included few big residues in TOP_HEAV(many atoms) library of Modeler and made changes everywhere required. It shows the following error; --------------------- penf5__224_> Open 11 OLD SEQUENTIAL ${MODINSTALL6v2}/modlib//top_heav.lib read_to_223E> Array too small. Increase MAPRES current maximum, current need: 100 101 recover____E> ERROR_STATUS >= STOP_ON_ERROR: 1 1 --------------------- what is the reason? Where I can get this variable MAPRES to change? I also tried to remove some residues from TOP_HEAV library but it didn't worked out, removing residues in such a way appears a bit strange, so please suggest a different solution if available. Also, as I have changed TOP_HEAV, restyp.lib is also needed to be changed or not, but as error suggest some problem in TOP_HEAV only? please suggest some solution. thanks in advance, best, vivek -- VIVEK SHARMA HBG BI

2 1

Hetatm error
by Shamshad Zarina 23 Aug '04

23 Aug '04

Dear Modeller users, I am facing a strange problem recently. I use linux version of modeller 6v2. I am trying to add NADP molecule to my protein. NADP is a part of template file and models are prepared without any problem. However, in one protein, one bond in NADP was missing in the final model file which was present in template. Another protein showed an oxygen atom in the vicinity of NADP without any bonds. There were no errors reported. I wonder where the actual bonds have gone. Any ideas? Best, Shamshad __________________________________ Do you Yahoo!? Yahoo! Mail is new and improved - Check it out! http://promotions.yahoo.com/new_mail

1 0

very low sequence identity...
by limnoha 21 Aug '04

21 Aug '04

I did a sequence-search but the signi scores of sequences were very low(below 4). How can I select the template among these sequences? Do you have any other method to do modelling a target like this? Do you have any example about this situation? Please help me... Thank you!!

1 0

few minute problems
by vivek sharma 11 Aug '04

11 Aug '04

Dear modeller people, these questions be a immature to ask as I don't know the complete algorithm, but as they came to my mind, so they are as follows; 1. If only optimization of molecular pdf is performed , not the molecular dynamics simulation, will there still be violations and if so then why, as molecular pdf optimization must keep all features in limits? 2. Is there any feature , which comes under category of both stereochemical as well as homology derived restraints? If then will that be optimized separately for both? best regards -- VIVEK SHARMA

1 0

Does Modeller work on x86_64?
by benne278 02 Aug '04

02 Aug '04

Has anyone used modeller successfully on an Intel x86_64 system? I am trying to use 6v2 on a 3.4 GHz machine running RedHat Enterprise 3 and Modeller seg-faults even on the supplied example jobs. My actual jobs crash too, of course, and they run fine on a PIII Linux system I have access to. So either my system is not configured correctly or there is a problem running on x86_64. Are there any libraries I should check, or any other issues I should be aware of for running on x86_64? The examples do this: [bennette@localhost examples]$ ./Run_tests DIR: ./align-model-steps /HOME/software/modeller/bin/mod6v2: line 38: 13124 Segmentation fault (core dumped) $NICE ${EXECUTABLE} $STEERF >$LOGF DIR: ./all-steps /HOME/software/modeller/bin/mod6v2: line 38: 13132 Segmentation fault (core dumped) $NICE ${EXECUTABLE} $STEERF >$LOGF STOP ... etc. ... The log file for my job shows that the program doesn't report any errors, it just dies after saying it is calculating distance restraints: http://abacavir.pharmacy.umn.edu/~bennette/modeller/model-default.log.txt Thanks for any suggestions, Dr. Eric Bennett Center for Drug Design University of Minnesota

2 1